Fake electronic components are a common reason a well-designed circuit fails, overheats or works on the bench and then dies in the field. Relabelled MOSFETs, remarked ICs and undersized capacitors are sold in local markets and online. This guide shows how to spot fake electronic components before they go on your board, and how to test the doubtful ones.

In this article
  • Warning signs before you buy
  • Visual checks on the part
  • Electrical tests for MOSFETs, capacitors and ICs
  • Where and how to buy safely
Buy a smallsample firstVisual checkmarking, leads, batchElectrical testRDS(on), C, ESR, IDMatchesdatasheet?yesOrder full batchfrom same lotnoReject the lot,change supplier
Screen every new batch before it goes on a board: sample, inspect, test against the datasheet, then decide.

Warning signs before you buy

  • The price is far below the normal distributor price. A popular power MOSFET or MCU selling for a fraction of its usual price is the strongest warning sign.
  • The seller cannot say where the stock came from. Genuine parts trace back to the manufacturer or an authorised distributor.
  • Obsolete or hard-to-find parts suddenly in large stock. These are often recovered from scrap and remarked.

Visual checks on the part

  • Marking quality: genuine parts usually have sharp laser marking. Blurry print, uneven fonts, or ink that rubs off with a cotton bud and isopropyl alcohol or acetone suggests remarking.
  • Signs of sanding: a scratched or unusually smooth top surface, or a coating that looks different from the sides.
  • Leads: bent, re-tinned or scratched leads point to parts pulled from old boards.
  • Mixed batches: different date codes, logos or package finishes in the same tube or reel.
  • Datasheet mismatch: compare the package size, pin-1 mark and marking format with the manufacturer’s datasheet.

Electrical tests for doubtful parts

MOSFETs

Fake power MOSFETs are often smaller dies in a big package, with much higher on-resistance than the datasheet. A simple check: drive the gate with 10 V, pass a known current (for example 2 A from a current-limited supply) through drain to source, and measure the voltage drop. RDS(on) = V ÷ I. If the result is several times higher than the datasheet value, do not use the part in an inverter or motor driver. Use our multimeter testing guide for the basic good/bad check first.

Electrolytic capacitors

Counterfeit or low-grade capacitors may show lower capacitance than marked, high ESR, or a lower voltage rating than printed. Measure the capacitance with your meter; if you have an ESR meter or a component tester, compare the ESR with a capacitor from a known brand of the same value.

ICs and microcontrollers

Read the device ID with your programmer: a remarked microcontroller often reports a different device ID or will not connect. For regulators and op-amps, build a small test jig and check the key datasheet values (output voltage, quiescent current, offset) before using a new batch.

🧮 Free tool for this topic

Where and how to buy safely

  • For production and critical designs, buy from the manufacturer’s authorised distributors and keep the invoices.
  • For local purchases, buy a small quantity first, test it, and then order the full batch from the same lot.
  • Keep a few known-genuine samples of the parts you use most, so you can compare markings and test results.
  • Build a simple test jig for your most-used parts. Our electronic component tester project is a good start.

Not sure whether a part is genuine? Send the part marking and your test readings on WhatsApp and we’ll take a look.


MKDas

Mithun K. Das. B.Sc. in Electrical and Electronic Engineering (EEE) from KUET. Senior Embedded Systems Designer at a leading international company. Welcome to my personal blog! I share articles on various electronics topics, breaking them down into simple and easy-to-understand explanations, especially for beginners. My goal is to make learning electronics accessible and enjoyable for everyone. If you have any questions or need further assistance, feel free to reach out through the Contact Us page. Thank you for visiting, and happy learning!

0 Comments

Leave a Reply

Avatar placeholder

Your email address will not be published. Required fields are marked *