Knowing how to test electronic components with a multimeter saves hours of guesswork. Before you replace a part or blame your code, a two-minute check with a digital multimeter (DMM) tells you whether a resistor, diode, capacitor or transistor is good. This guide shows the exact meter mode, probe placement and the readings to expect for each part.
- Safety and meter set-up
- Resistors and continuity
- Diodes and LEDs
- Capacitors
- BJT transistors and MOSFETs
- Quick reference table
Table of Contents
Before you start: safety and set-up
- Power off and discharge. Never measure resistance, diodes or capacitors on a powered board. Large capacitors in SMPS and inverters can hold dangerous voltage after switch-off; discharge them through a suitable resistor first.
- Test out of circuit when you can. Other parts in parallel change the reading. If an in-circuit reading looks wrong, lift one leg and measure again.
- Check the meter itself. Touch the probes together: resistance should read close to 0 Ω and the continuity buzzer should sound.
- Use the right jacks. Black probe in COM, red probe in the V/Ω jack. Leaving the red lead in the 10 A jack is a common way to blow the meter fuse.
How to test a resistor
Select the Ω range (or auto-range) and touch the probes to both ends. The reading should match the colour code within its tolerance: ±5% for gold-band resistors and ±1% for brown-band metal-film parts. An open (OL) reading means the resistor is burnt open; a value far above the marking usually means it has been overheated.
Not sure what the bands mean? Use our resistor colour code calculator to decode 4- and 5-band resistors.
Continuity: finding broken tracks and wires
Continuity mode beeps when the resistance between the probes is low (typically below a few tens of ohms, depending on the meter). Use it to check fuses, switches, cables and PCB tracks. Remember that a low-value resistor or an inductor will also beep.
How to test a diode and an LED
Switch to diode-test mode (the diode symbol). The meter pushes a small current and shows the forward voltage drop.
- Red probe on the anode, black on the cathode (the band side): a good silicon diode reads about 0.5–0.7 V; a Schottky diode about 0.15–0.35 V.
- Reverse the probes: a good diode shows OL (open).
- Low reading both ways = shorted diode. OL both ways = open diode.
- Red and many green LEDs often glow faintly in diode mode and read about 1.6–2.2 V. Blue and white LEDs need about 2.7–3.2 V, which some meters cannot supply, so an OL reading does not prove a blue LED is dead.
How to test a capacitor
Discharge the capacitor, then use the capacitance range (often marked with the capacitor symbol or F). The reading should be within the tolerance printed on the part; electrolytics are often −20%/+20% or wider. A reading far below the rating means the capacitor has dried out.
A normal multimeter cannot measure ESR (equivalent series resistance), which is the usual failure in SMPS output capacitors. A capacitor can show the right capacitance and still fail in circuit. Swollen tops, leaking electrolyte or a brown residue are clear signs to replace it.
How to test a BJT transistor
Think of an NPN transistor as two diodes that share the base. In diode mode:
- NPN: red on base, black on emitter → about 0.6–0.7 V. Red on base, black on collector → about 0.6–0.7 V.
- PNP: same test with the probes reversed (black on base).
- Collector to emitter should read OL in both directions.
- Any reading near 0 V means a shorted junction; the transistor is bad.
Many meters also have an hFE socket that shows the current gain. Use it as a quick good/bad check only; the number varies a lot with current.
How to test a MOSFET
For an N-channel enhancement MOSFET in diode mode:
- Short gate to source with your finger or a wire to discharge the gate.
- Red on source, black on drain: you should see the body diode, about 0.4–0.7 V. Reversed (red on drain, black on source): OL.
- Now touch red to gate and black to source for a second. This charges the gate.
- Measure drain to source again (red on drain): it should now read low, because the channel is switched on.
- Short gate to source again and the reading should go back to OL. If drain–source is low before you charge the gate, the MOSFET is shorted, which is the most common failure in inverters and motor drivers.
For a P-channel MOSFET, reverse all polarities.
- Ohm’s law & power calculator – check the expected current and power in any part
- LED series resistor calculator – pick the right resistor after replacing an LED
Quick reference: what a good part reads
| Component | Meter mode | Good reading | Bad reading |
|---|---|---|---|
| Resistor | Ω | Marked value ± tolerance | OL or far off value |
| Silicon diode | Diode | 0.5–0.7 V forward, OL reverse | Low both ways or OL both ways |
| Schottky diode | Diode | 0.15–0.35 V forward, OL reverse | Low both ways |
| Capacitor | Capacitance | Within rated tolerance | Much lower, or short |
| NPN transistor | Diode | B–E and B–C about 0.6–0.7 V, C–E OL | Near 0 V on any pair |
| N-MOSFET | Diode | Body diode 0.4–0.7 V; D–S OL until gate charged | D–S low with gate discharged |
Which multimeter should you buy?
For students and hobby work, an auto-ranging meter with diode, continuity and capacitance modes is enough. For mains work, choose a meter with a proper CAT III rating and fused current inputs. See our ANENG 683 multimeter review for a low-cost option, or build our electronic component tester project to identify parts automatically.
Stuck with a part that won’t test right? Send a photo of the board and your readings on WhatsApp and we’ll help you find the fault.
0 Comments