Lab Projects BD
  • Home
  • Services & Portfolio
  • Projects
  • Tutorials
    • All Topics
    • Microcontrollers & EmbeddedArduino, ESP32, STM32, PIC, 8051, Raspberry Pi, IoT Projects, Trainer Kits, Embedded Products
    • Power ElectronicsElectronics, Power Supplies, Analog Electronics, Batteries, Renewable Energy, Home Appliances
    • IoT & Emerging TechArtificial Intelligence, Future Electronics, Productivity, Project Ideas
    • PCB DesignPCB Design, Complete Projects, DIY Projects, EEPROM, Meters & Displays, GSM, RFID
    • Lab Tools & TechniquesReviews, Buying Guides, Lab Essentials, Measuring Instruments, Troubleshooting, Design Tools
    • Student & Local Help
  • Tools
    • Ohm’s Law & Power
    • Resistor Colour Code
    • 555 Timer
    • RC Time Constant
    • LED Resistor
    • Voltage Divider / ADC
    • PCB Trace Width
    • IPS / Inverter Size
    • Battery Backup Time
    • Solar System Size
    • Electricity Units & Bill
    • CT Burden Resistor
  • About
  • Contact

Op-amp circuits

Op-amp circuits explained: amplifiers, comparators, current sensing and analog stabilizer control.

PCB Design

Op-Amp Application Trainer Kit for Analog Electronics Laboratories

Operational amplifiers are one of the most fundamental building blocks in analog electronics. From signal conditioning to oscillators and filters, op-amps are used in almost every electronic system. However, students often struggle to understand op-amp behavior without hands-on experimentation. In this article Purpose of This Op-Amp Trainer Kit Built-in Op-Amp Read more

By MKDas, 11 months03/01/2026 ago
Microcontrollers & Embedded

How to design an Analog voltage stabilizer using Relays and LM324 Op-Amp and NE555 Timer IC

Design an analog voltage stabilizer without a microcontroller using LM324 comparators, an NE555 delay timer and relays: block diagram, transformer and full circuit.

By MKDas, 6 years16/04/2021 ago
Power Electronics

DC Current measurement using Shunt resistor and Op-Amp Circuit

In this article, we will discuss DC Current measurement using Shunt. Measuring current sometimes becomes very necessary in electronics circuits. We can measure DC current using current sensors or by using simple shunt resistors. In this article, I’m going to discuss DC current measurement techniques and different circuits for this Read more

By MKDas, 7 years09/05/2020 ago
Power Electronics

Making a High Voltage AC voltmeter with Arduino UNO and Op-Amp circuit, Measure 2500V !!!

In this article, we are going to learn how to make a high voltage AC voltmeter using Arduino and we are going to measure 2500V. Utilizing the technique shown here, we can even measure more than this range. So let’s start our High Voltage AC voltmeter. ⏱ 5 min read Read more

By MKDas, 7 years08/05/2020 ago
Power Electronics

High voltage DC measurement using Arduino

In this article, we are going to measure high voltage using Arduino. Measuring over 1500V is not safe to work at all. But sometimes, we need to implement such a meter. Here in this article, we will make a high voltage DC voltmeter with Arduino UNO that can measure over Read more

By MKDas, 7 years08/05/2020 ago
Power Electronics

How to make a high voltage DC voltmeter (1000V+ !!!)

Like the high voltage AC meter, we can use the same Op-Amp circuit to measure high voltage DC voltmeter. In this article, we are going to learn how to make a high voltage DC voltmeter using a micro-controller and Op-Amp circuitry. ⏱ 3 min read · 🔧 Includes: diagrams & Read more

By MKDas, 7 years05/05/2020 ago
Power Electronics

How to make a high voltage AC voltmeter

In our previous articles, we learned how to make an AC voltmeter and how to measure high voltage AC voltage. In this article, we will learn how to make a high voltage AC voltmeter. Yes, you can measure 500V+ or higher easily with this circuitry. ⏱ 5 min read · Read more

By MKDas, 7 years04/05/2020 ago
Power Electronics

How to measure floating high voltage AC with Op-Amp

Measuring high voltage AC is not safe just with a resistor voltage divider. Or sometimes, we can not connect one terminal to the GND of the measuring circuit. Sometimes, we need to measure a floating high voltage. In this article, we are going to learn how to do that floating Read more

By MKDas, 7 years04/05/2020 ago
Power Electronics

how to generate a pure sine wave using an Op-Amp

Hi, you can generate a pure sine wave just using an Op-Amp. It is very simple and can be used in many applications. In this article, we are going to learn how to generate a pure sine wave using an Op-Amp. ⏱ 2 min read · 🔧 Includes: diagrams & Read more

By MKDas, 7 years23/04/2020 ago
Subscribe to Blog

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Loading
Categories
Recent Posts
  • How to Spot Fake Electronic Components (MOSFETs, ICs, Capacitors) Before They Ruin Your Project
  • How to Troubleshoot a Dead Circuit Board: A Step-by-Step Repair Method
  • Why Does My IPS Battery Die So Fast? 8 Causes and How to Fix Them
  • How to Test Electronic Components with a Multimeter (Resistor, Diode, Capacitor, Transistor)
  • Final-Year EEE Project Ideas for Students in Bangladesh (Beginner to Advanced)
Archives

Follow on Facebook →

About

Lab Projects BD is your go-to destination for electronics and embedded systems tutorials, projects, and resources. With a focus on helping beginners and enthusiasts alike, the website provides a wealth of information on Arduino, Raspberry Pi, and other microcontrollers. From IoT to robotics and home automation, Lab Projects BD has it all. Join the community and take your electronics skills to the next level.

Recent Posts
  • How to Spot Fake Electronic Components (MOSFETs, ICs, Capacitors) Before They Ruin Your Project
  • How to Troubleshoot a Dead Circuit Board: A Step-by-Step Repair Method
  • Why Does My IPS Battery Die So Fast? 8 Causes and How to Fix Them

  • Recommended Tools
  • Privacy Policy
  • Contact
Hestia | Developed by ThemeIsle
pixel